Buy BOSS Audio Systems R2400D - Riot 2400 Watt, 1, 2, 4 Ohm Stable Class D Monoblock Car Amplifier with Remote Subwoofer Control: Mono Amplifiers - Amazon.com FREE DELIVERY possible on eligible purchases. The minimalist design of the BOSS Audio R2504 RIOT Series 1000W Mosfet Power 4-Channel Amplifier has the ability to produce power output to the maximum of 250W and 90W of RMS. Featuring a blue illuminated Boss logo, the 1000W MOSFET unit also includes a remote subwoofer level control.
JOHN DEERE WORLDWIDE COMMERCIAL & CONSUMER EQUIPMENT DIVISION Lawn Tractors LTR155, LTR166 and LTR180 OMTM1768 FEBRUARY 2002 TECHNICAL MANUAL Litho in U.S.A. North American Version Litho in U.S.A. INTRODUCTION This technical manual is written for an experienced technician and contains sections that are specifically for this product. It is a part of a total product support program.
Safety Specifications and Information Kohler Engine Briggs & Stratton Engine Kawasaki Engine Electrical Power Train (Hydrostatic) Steering The manual is organized so that all the information on a particular system is kept together. The order of grouping is as follows:. Table of Contents General Diagnostic Information Specifications Electrical Wiring Harness Legend Component Location System Schematic Wiring Harness Troubleshooting Chart Theory of Operation Diagnostics Tests & Adjustments Repair Note: Depending on the particular section or system being covered, not all of the above groups may be used. Each section will be identified with a symbol rather than a number. The groups and pages within a section will be consecutively numbered. We appreciate your input on this manual.
To help, there are postage paid post cards included at the back. If you find any errors or want to comment on the layout of the manual please fill out one of the cards and mail it back to us. Attachments All information, illustrations and specifications in this manual are based on the latest information available at the time of publication. The right is reserved to make changes at any time without notice. Miscellaneous COPYRIGHT© 2002 Deere and Co. John Deere Worldwide Commercial and Consumer Equipment Division Horicon, WI All rights reserved 3/6/02 1-1 SAFETY SAFETY RECOGNIZE SAFETY INFORMATION HANDLE FLUIDS SAFELY-AVOID FIRES BE PREPARED FOR EMERGENCIES This is the safety-alert symbol. When you see this symbol on your machine or in this manual, be alert to the potential for personal injury.
Follow recommended precautions and safe servicing practices. UNDERSTAND SIGNAL WORDS A signal word—DANGER, WARNING, or CAUTION—is used with the safety-alert symbol. DANGER identifies the most serious hazards. DANGER identifies the most serious hazards.
Danger or Warning safety signs are located near specific hazards. CAUTION safety signs are used where general precautions should be used. CAUTION also calls attention to safety messages in this manual. When you work around fuel, do not smoke or work near heaters or other fire hazards.
Store flammable fluids away from fire hazards. Do not incinerate or puncture pressurized containers.
Make sure machine is clean of trash, grease, and debris. Do not store oily rags; they can ignite and burn spontaneously. Be prepared if a fire starts. Keep a first aid kit and fire extinguisher handy.
Keep emergency numbers for doctors, ambulance service, hospital, and fire department near your telephone. REPLACE SAFETY SIGNS Replace missing or damaged safety signs. See the machine operator’s manual for correct safety sign placement. 1-2 3/6/02 SAFETY USE CARE IN HANDLING AND SERVICING BATTERIES USE SAFE SERVICE PROCEDURES WEAR PROTECTIVE CLOTHING PREVENT BATTERY EXPLOSIONS.
Keep sparks, lighted matches, and open flame away from the top of battery. Battery gas can explode. Never check battery charge by placing a metal object across the posts. Use a volt-meter or hydrometer. Do not charge a frozen battery; it may explode.
Warm battery to 16°C (60°F). Wear close fitting clothing and safety equipment appropriate to the job. Prolonged exposure to loud noise can cause impairment or loss of hearing. Wear a suitable hearing protective device such as earmuffs or earplugs to protect against objectionable or uncomfortable loud noises. Operating equipment safely requires the full attention of the operator.
Do not wear radio or music headphones while operating machine. PREVENT ACID BURNS. Sulfuric acid in battery electrolyte is poisonous. It is strong enough to burn skin, eat holes in clothing, and cause blindness if splashed into eyes. Avoid acid burns by: 1.
Filling batteries in a well-ventilated area. Wearing eye protection and rubber gloves. Avoiding breathing fumes when electrolyte is added. Avoiding spilling or dripping electrolyte. Use proper jump start procedure.
If you spill acid on yourself: 1. Flush your skin with water. Apply baking soda or lime to help neutralize the acid. Flush your eyes with water for 1015 minutes.
Get medical attention immediately. If acid is swallowed: 1.
Drink large amounts of water or milk. Then drink milk of magnesia, beaten eggs, or vegetable oil. Get medical attention immediately. SERVICE MACHINES SAFELY Tie long hair behind your head. Do not wear a necktie, scarf, loose clothing, or necklace when you work near machine tools or moving parts. If these items were to get caught, severe injury could result.
Remove rings and other jewelry to prevent electrical shorts and entanglement in moving parts. USE PROPER TOOLS Use tools appropriate to the work.
Makeshift tools and procedures can create safety hazards. Use power tools only to loosen threaded parts and fasteners. For loosening and tightening hardware, use the correct size tools.
DO NOT use U.S. Measurement tools on metric fasteners. Avoid bodily injury caused by slipping wrenches. Use only service parts meeting John Deere specifications. 3/6/02 1-3 SAFETY PARK MACHINE SAFELY USING HIGH PRESSURE WASHERS Directing pressurized water at electronic/electrical components or connectors, bearings, hydraulic seals, fuel injection pumps or other sensitive parts and components may cause product malfunctions.
Reduce pressure and spray at a 45 to 90 degree angle. ILLUMINATE WORK AREA SAFELY Illuminate your work area adequately but safely.
Use a portable safety light for working inside or under the machine. Make sure the bulb is enclosed by a wire cage. The hot filament of an accidentally broken bulb can ignite spilled fuel or oil. Before working on the machine: 1. Lower all equipment to the ground. Stop the engine and remove the key. Disconnect the battery ground strap.
Hang a “DO NOT OPERATE” tag in operator station. WORK IN VENTILATED AREA SUPPORT MACHINE PROPERLY AND USE PROPER LIFTING EQUIPMENT Engine exhaust fumes can cause sickness or death. If it is necessary to run an engine in an enclosed area, remove the exhaust fumes from the area with an exhaust pipe extension. If you do not have an exhaust pipe extension, open the doors and get outside air into the area.
If you must work on a lifted machine or attachment, securely support the machine or attachment. Do not support the machine on cinder blocks, hollow tiles, or props that may crumble under continuous load. Do not work under a machine that is supported solely by a jack. Follow recommended procedures in this manual. Lifting heavy components incorrectly can cause severe injury or machine damage. Follow recommended procedure for removal and installation of components in the manual. WARNING: CALIFORNIA PROPOSITION 65 WARNING Gasoline engine exhaust from this product contains chemicals known to the State of California to cause cancer, birth defects, or other reproductive harm.
REMOVE PAINT BEFORE WELDING OR HEATING Avoid potentially toxic fumes and dust. Hazardous fumes can be generated when paint is heated by welding, soldering, or using a torch.
Do all work outside or in a well ventilated area. Dispose of paint and solvent properly. Remove paint before welding or heating: If you sand or grind paint, avoid breathing the dust.
Wear an approved respirator. If you use solvent or paint stripper, remove stripper with soap and water before welding.
Remove solvent or paint stripper containers and other flammable material from area. Allow fumes to disperse at least 15 minutes before welding or heating. WORK IN CLEAN AREA Before starting a job: 1. Clean work area and machine.
Make sure you have all necessary tools to do your job. Have the right parts on hand.
Read all instructions thoroughly; do not attempt shortcuts. 1-4 3/6/02 SAFETY AVOID HARMFUL ASBESTOS DUST Avoid breathing dust that may be generated when handling components containing asbestos fibers. Inhaled asbestos fibers may cause lung cancer. Components in products that may contain asbestos fibers are brake pads, brake band and lining assemblies, clutch plates, and some gaskets. The asbestos used in these components is usually found in a resin or sealed in some way. Normal handling is not hazardous as long as airborne dust containing asbestos is not generated.
Avoid creating dust. Never use compressed air for cleaning. Avoid brushing or grinding material containing asbestos. When servicing, wear an approved respirator.
A special vacuum cleaner is recommended to clean asbestos. If not available, apply a mist of oil or water on the material containing asbestos. Keep bystanders away from the area. AVOID INJURY FROM ROTATING BLADES, AUGERS AND PTO SHAFTS Keep hands and feet away while machine is running. Shut off power to service, lubricate or remove mower blades, augers or PTO shafts.
SERVICE TIRES SAFELY HANDLE CHEMICAL PRODUCTS SAFELY Explosive separation of a tire and rim parts can cause serious injury or death. Do not attempt to mount a tire unless you have the proper equipment and experience to perform the job. Always maintain the correct tire pressure. Do not inflate the tires above the recommended pressure. Never weld or heat a wheel and tire assembly. The heat can cause an increase in air pressure resulting in a tire explosion.
Welding can structurally weaken or deform the wheel. When inflating tires, use a clip-on chuck and extension hose long enough to allow you to stand to one side and NOT in front of or over the tire assembly.
Use a safety cage if available. Check wheels for low pressure, cuts, bubbles, damaged rims or missing lug bolts and nuts. Direct exposure to hazardous chemicals can cause serious injury.
Potentially hazardous chemicals used with John Deere equipment include such items as lubricants, coolants, paints, and adhesives. A Material Safety Data Sheet (MSDS) provides specific details on chemical products: physical and health hazards, safety procedures, and emergency response techniques.
Check the MSDS before you start any job using a hazardous chemical. That way you will know exactly what the risks are and how to do the job safely. Then follow procedures and recommended equipment. 3/6/02 1-5 SAFETY DISPOSE OF WASTE PROPERLY Improperly disposing of waste can threaten the environment and ecology. Potentially harmful waste used with John Deere equipment include such items as oil, fuel, coolant, brake fluid, filters, and batteries. Use leakproof containers when draining fluids. Do not use food or beverage containers that may mislead someone into drinking from them.
The new Instructor’s eText gives instructors easy access to videos, readings, and more within their eText. It collects the very best class presentation resources - art and figures from our leading texts, videos, lecture activities, classroom activities, demonstrations, and much more - in one convenient online destination. • Class Preparation Tool- Class Preparation Tool makes lecture preparation simpler and less time consuming. Essential sociology 12th edition pdf. Found within MySocLab, it is the one location to find all available instructor resources.
Do not pour waste onto the ground, down a drain, or into any water source. Inquire on the proper way to recycle or dispose of waste from your local environmental or recycling center, or from your John Deere dealer. LIVE WITH SAFETY Before returning machine to customer, make sure machine is functioning properly, especially the safety systems.
Install all guards and shields. 1-6 3/6/02 SPECIFICATIONS AND INFORMATION CONTENTS CONTENTS Page SPECIFICATIONS GENERAL VEHICLE SPECIFICATIONS. 3 KOHLER ENGINE—LTR155.
3 BRIGGS & STRATTON ENGINE—LTR166. 3 KAWASAKI ENGINE—LTR180. 3 ELECTRICAL. 4 HYDROSTATIC TRANSAXLE. 4 PTO DRIVE.
4 STEERING. 4 IMPLEMENT LIFT. 4 TIRES. 4 DIMENSIONS. 4 REAR DISCHARGE MOWER DECK.
4 DRAWBAR LOAD. 4 GRASS COLLECTION SYSTEM.
4 TORQUE SPECIFICATIONS. 5 METRIC FASTENER TORQUE VALUES. 5 INCH FASTENER TORQUE VALUES. 6 FUEL AND OIL SPECIFICATIONS. 7 GASOLINE. 7 GASOLINE STORAGE— NORTH AMERICA.
7 ENGINE OIL. 8 ENGINE BREAK–IN OIL.
8 LUBRICANT SPECIFICATIONS. 9 ANTI-CORROSION GREASE. 9 ALTERNATIVE LUBRICANTS. 10 SYNTHETIC LUBRICANTS. 10 LUBRICANT STORAGE.
10 MIXING OF LUBRICANTS. 10 CHASSIS GREASE. 10 HYDROSTATIC TRANSMISSION OIL. 11 PRODUCT IDENTIFICATION LOCATIONS.
11 PRODUCT IDENTIFICATION NUMBER (PIN). 11 ENGINE IDENTIFICATION NUMBER—KOHLER. 12 ENGINE IDENTIFICATION NUMBER—BRIGGS & STRATTON. 12 ENGINE IDENTIFICATION NUMBER—KAWASAKI. 12 HYDROSTATIC TRANSAXLE IDENTIFICATION NUMBER.
12 3/6/02 2-1 NOTES SPECIFICATIONS AND INFORMATION 2-2 3/6/02 SPECIFICATIONS & INFORMATION GENERAL VEHICLE SPECIFICATIONS GENERAL VEHICLE SPECIFICATIONS KOHLER ENGINE—LTR155 Make. Kohler Model / Model Number. Command 15 QT / CV15S-41562 Power. 11.2 kW (15.0 hp) Displacement.426 cm3 (26.0 cu-in.) Cylinders. 1 Stroke/Cycle.
4 Valves. Overhead Valves Lubrication.Pressurized Gerotor Pump 0 – 413 kPa (0 – 60 psi) Oil Filter. Single Element, Full Flow, Spin-On Filter Crankcase Capacity (With Filter). 1.8 L (1.9 U.S. Oz) Without Filter. 1.4 L (1.5 U.S.
Oz) Cooling System. Air Cooled Air Cleaner. Paper with outer foam element Muffler.
Horizontal discharge below frame BRIGGS & STRATTON ENGINE—LTR166 Make. Briggs & Stratton Series. Vanguard V-Twin Type. 916928 Gasoline Model. 303777 Horsepower. 11.94 kW (16.0 hp) Displacement.
480 cm3 (29.3 cu. In.) Cylinders. 2 Stroke/Cycle.
4 Valves. Overhead Valves Lubrication. Pressurized 0 – 344 kPa (10 – 50 psi) Oil Filter. Full Flow Filter (w/o By-Pass Valve) Crankcase Capacity (With Filter).
1.5 L (1.6 U.S. Oz) Without Filter. 1.4 L (1.5 U.S. Oz) Cooling System. Air Cooled Air Cleaner. Paper with outer foam element Muffler.
Horizontal discharge below frame KAWASAKI ENGINE—LTR180 Make. Kawasaki Model. FH500V-AS32 V-Twin Horsepower. 12.7 kW (17.0 hp) Displacement. 494 cm3 (30.0 cu.
In.) Cylinders. 2 Stroke/Cycle. 4 Valves. Overhead Valves Lubrication. Pressurized Oil Filter. Single Element, Full Flow, Spin-On Filter Crankcase Capacity (With Filter). 1.7 L (1.8 U.S.
Oz) Without Filter. 1.5 L (1.6 U.S. Oz) Cooling System. Air Cooled Air Cleaner.
Paper with outer foam element Muffler. Horizontal discharge below frame 3/6/02 2-3 GENERAL VEHICLE SPECIFICATIONS SPECIFICATIONS & INFORMATION FUEL SYSTEM Aspiration.Natural Fuel Tank Location.Rear Fuel Tank Capacity. 6.0 L (1.6 U.S. Gal) Fuel Type (minimum octane).
Unleaded Gasoline, 87 Octane Fuel Delivery. Float-Type Side Draft CArburetor Fuel Filter. Replaceable In-Line ELECTRICAL Ignition.Electronic Capacitor Discharge Ignition (CDI) Type of Starter. Bendix Charging System. Flywheel Alternator Voltage.
12 BCI group.U-1 CCA rating (Amps At -18°C (0°F). 160 Reserve capacity (Minutes At 25 Amps). 20 Specific gravity (Minimum).1.225 points Electrolyte required fill (Approximate). 1.9 L (2.0 qt) Load test (Minimum). 255 amp for 15 seconds HYDROSTATIC TRANSAXLE Drive Train. Belt Drive Transaxle with foot-controlled variable speed drive Model.Tuff Torq® K46 Transaxle Travel Speed-Forward.
0 – 8.0 km/h (0 – 5.0 mph) Travel Speed-Reverse. 0 – 4.7 km/h (0 – 2.9 mph) Brake type.Single, Internal Wet Disc Brake PTO DRIVE Type. V-Belt Clutch Type.
Mechanical Control. Lever on Dash STEERING Type. Sector and Pinion Turning Radius. 38.1 cm (15 in.) IMPLEMENT LIFT Lift System.Manual Lift Lever Location. Left Side TIRES Size-Front. 15x6.00-6 Size-Rear. 20x10.00-8 Pressure-Front (with mower).
83 kPa (12 psi) Pressure-Rear (with mower). 55 kPa (8 psi) DIMENSIONS Wheelbase.
Boss Amp 250n Manual Lawn Mower
120 cm (47.2 in.) Overall Length. 197.7 cm (77.8 in.) With Grass Collector. 241.5 cm (95.1 in.) Overall Width (without mower). 92 cm (36.2 in.) Overall Height. 103 cm (40.6 in.) Net Weight (Approx.).
This is the Highly Detailed factory service repair manual for theJOHN DEERE STX38 LAWN GARDEN TRACTOR, this Service Manual has detailed illustrations as well as step by step instructions,It is 100 percents complete and intact. They are specifically written for the do-it-yourself-er as well as the experienced mechanic.JOHN DEERE STX38 LAWN GARDEN TRACTOR Service Repair Workshop Manual provides step-by-step instructions based on the complete dis-assembly of the machine. It is this level of detail, along with hundreds of photos and illustrations, that guide the reader through each service and repair procedure. Complete download comes in pdf format which can work under all PC based windows operating system and Mac also, All pages are printable. Using this repair manual is an inexpensive way to keep your vehicle working properly. Service Repair Manual Covers: Safety Specifications and information Engine Electrical Gear Power train Hydrostatic Power train Steering Miscellaneous Index File Format: PDF Compatible: All Versions of Windows & Mac Language: English Requirements: Adobe PDF Reader NO waiting, Buy from responsible seller and get INSTANT DOWNLOAD, Without wasting your hard-owned money on uncertainty or surprise! All pages are is great to haveJOHN DEERE STX38 LAWN GARDEN TRACTOR Service Repair Workshop Manual.
Looking for some other Service Repair Manual,please check: Thanks for visiting! JOHN DEERE STX38 LAWN GARDEN TRACTOR Service Repair Manual. 1. TECHNICAL MANUAL Litho in U.S.A John Deere Worldwide Commercial and Consumer Equipment Division STX30, STX38, and STX46 Lawn Tractors TM1561 (15Mar97) Replaces TM1561 (01Sep95) and TM1418 (26Oct92). M55912 M55913 M3M58332 STX38 Gear Drive STX38 Hydrostatic Drive STX46 Hydrostatic DriveSTX46 Gear Drive STX38 Motorsport Edition M85680. INTRODUCTION 3/12/97 1 - 1 This technical manual is written for an experienced technician and contains sections that are specifically for this product. It is a part of a total product support program.
The manual is organized so that all the information on a particular system is kept together. The order of grouping is as follows:. Table of Contents. Specifications. Theory of Operation.
Troubleshooting Diagram. Diagnostics. Tests & Adjustments. Repair Note: Depending on the particular section or system being covered, not all of the above groups may be used.
Each section will be identified with a symbol rather than a number. The groups and pages within a section will be consecutively numbered. All information, illustrations and specifications in this manual are based on the latest information available at the time of publication. The right is reserved to make changes at any time without notice.
We appreciate your input on this manual. To help, there are postage paid post cards included at the back. If you find any errors or want to comment on the layout of the manual please fill out one of the cards and mail it back to us.
COPYRIGHT© 1997 JOHN DEERE HORICON WORKS Horicon, Wisconsin All rights reserved Information Specifications and Engine Electrical Power Train Power Train (Hydrostatic) Steering Safety Miscellaneous Power Train (Gear). SAFETY 1 - 2 3/12/97 RECOGNIZE SAFETY INFORMATION This is the safety-alert symbol. When you see this symbol on your machine or in this manual, be alert to the potential for personal injury. Follow recommended precautions and safe servicing practices. Understand Signal Words A signal word—DANGER, WARNING, or CAUTION— is used with the safety-alert symbol.
DANGER identifies the most serious hazards. DANGER or WARNING safety signs are located near specific hazards. General precautions are listed on CAUTION safety signs. CAUTION also calls attention to safety messages in this manual. REPLACE SAFETY SIGNS Replace missing or damaged safety signs. See the machine operator’s manual for correct safety sign placement. HANDLE FLUIDS SAFELY-AVOID FIRES Be Prepared For Emergencies When you work around fuel, do not smoke or work near heaters or other fire hazards.
Store flammable fluids away from fire hazards. Do not incinerate or puncture pressurized containers. Make sure machine is clean of trash, grease, and debris. Do not store oily rags; they can ignite and burn spontaneously. Be prepared if a fire starts.
Keep a first aid kit and fire extinguisher handy. Keep emergency numbers for doctors, ambulance service, hospital, and fire department near your telephone.
SAFETY 3/12/97 1 - 3 USE CARE IN HANDLING AND SERVICING BATTERIES Prevent Battery Explosions. Keep sparks, lighted matches, and open flame away from the top of battery.
Battery gas can explode. Never check battery charge by placing a metal object across the posts.
Use a volt-meter or hydrometer. Do not charge a frozen battery; it may explode. Warm battery to 16°C (60°F).
Prevent Acid Burns. Sulfuric acid in battery electrolyte is poisonous. It is strong enough to burn skin, eat holes in clothing, and cause blindness if splashed into eyes. Avoid acid burns by: 1.
Filling batteries in a well-ventilated area. Wearing eye protection and rubber gloves. Avoiding breathing fumes when electrolyte is added. Avoiding spilling or dripping electrolyte. Use proper jump start procedure. If you spill acid on yourself: 1.
Flush your skin with water. Apply baking soda or lime to help neutralize the acid. Flush your eyes with water for 1015 minutes. Get medical attention immediately. If acid is swallowed: 1.
Drink large amounts of water or milk. Then drink milk of magnesia, beaten eggs, or vegetable oil. Get medical attention immediately. USE CARE AROUND HIGH- PRESSURE FLUID LINES Avoid High-pressure Fluids Escaping fluid under pressure can penetrate the skin causing serious injury.
Avoid injury from escaping fluid under pressure by stopping the engine and relieving pressure in the system before disconnecting or connecting hydraulic or other lines. Tighten all connections before applying pressure. Search for leaks with a piece of cardboard. Protect hands and body from high pressure fluids. If an accident occurs, see a doctor immediately. Any fluid injected into the skin must be surgically removed within a few hours or gangrene may result.
Doctors unfamiliar with this type of injury should reference a knowledgeable medical source. Such information is available from Deere & Company Medical Department in Moline, Illinois, U.S.A. Avoid Heating Near Pressurized Fluid Lines Flammable spray can be generated by heating near pressurized fluid lines, resulting in severe burns to yourself and bystanders. Do not heat by welding, soldering, or using a torch near pressurized fluid lines or other flammable materials. Pressurized lines can be accidentally cut when heat goes beyond the immediate flame area. SAFETY 1 - 4 3/12/97 USE SAFE SERVICE PROCEDURES Wear Protective Clothing Wear close fitting clothing and safety equipment appropriate to the job.
Prolonged exposure to loud noise can cause impairment or loss of hearing. Wear a suitable hearing protective device such as earmuffs or earplugs to protect against objectionable or uncomfortable loud noises. Operating equipment safely requires the full attention of the operator. Do not wear radio or music headphones while operating machine. Service Machines Safely Tie long hair behind your head. Do not wear a necktie, scarf, loose clothing, or necklace when you work near machine tools or moving parts. If these items were to get caught, severe injury could result.
Remove rings and other jewelry to prevent electrical shorts and entanglement in moving parts. Use Proper Tools Use tools appropriate to the work. Makeshift tools and procedures can create safety hazards.
Use power tools only to loosen threaded parts and fasteners. For loosening and tightening hardware, use the correct size tools.
DO NOT use U.S. Measurement tools on metric fasteners. Avoid bodily injury caused by slipping wrenches. Use only service parts meeting John Deere specifications. Park Machine Safely Before working on the machine: 1. Lower all equipment to the ground. Stop the engine and remove the key.
Disconnect the battery ground strap. Hang a “DO NOT OPERATE” tag in operator station. Support Machine Properly And Use Proper Lifting Equipment If you must work on a lifted machine or attachment, securely support the machine or attachment. Do not support the machine on cinder blocks, hollow tiles, or props that may crumble under continuous load.
Do not work under a machine that is supported solely by a jack. Follow recommended procedures in this manual. Lifting heavy components incorrectly can cause severe injury or machine damage.
Boss Amp 250n Manual Lawn Service
Follow recommended procedure for removal and installation of components in the manual. Work In Clean Area Before starting a job: 1. Clean work area and machine. Make sure you have all necessary tools to do your job. Have the right parts on hand. Read all instructions thoroughly; do not attempt shortcuts.
SAFETY 3/12/97 1 - 5 Using High Pressure Washers Directing pressurized water at electronic/electrical components or connectors, bearings, hydraulic seals, fuel injection pumps or other sensitive parts and components may cause product malfunctions. Reduce pressure and spray at a 45 to 90 degree angle. Illuminate Work Area Safely Illuminate your work area adequately but safely. Use a portable safety light for working inside or under the machine.
Make sure the bulb is enclosed by a wire cage. The hot filament of an accidentally broken bulb can ignite spilled fuel or oil. Work In Ventilated Area Engine exhaust fumes can cause sickness or death. If it is necessary to run an engine in an enclosed area, remove the exhaust fumes from the area with an exhaust pipe extension. If you do not have an exhaust pipe extension, open the doors and get outside air into the area.
WARNING: California Proposition 65 Warning Diesel engine exhaust and some of its constituents are known to the State of California to cause cancer, birth defects, and other reproductive harm. Gasoline engine exhaust from this product contains chemicals known to the State of California to cause cancer, birth defects, or other reproductive harm. Remove Paint Before Welding Or Heating Avoid potentially toxic fumes and dust. Hazardous fumes can be generated when paint is heated by welding, soldering, or using a torch. Do all work outside or in a well ventilated area.
Dispose of paint and solvent properly. Remove paint before welding or heating: If you sand or grind paint, avoid breathing the dust. Wear an approved respirator.
If you use solvent or paint stripper, remove stripper with soap and water before welding. Remove solvent or paint stripper containers and other flammable material from area. Allow fumes to disperse at least 15 minutes before welding or heating. Avoid Harmful Asbestos Dust Avoid breathing dust that may be generated when handling components containing asbestos fibers. Inhaled asbestos fibers may cause lung cancer.
Components in products that may contain asbestos fibers are brake pads, brake band and lining assemblies, clutch plates, and some gaskets. The asbestos used in these components is usually found in a resin or sealed in some way. Normal handling is not hazardous as long as airborne dust containing asbestos is not generated. Avoid creating dust. Never use compressed air for cleaning. Avoid brushing or grinding material containing asbestos. When servicing, wear an approved respirator.
A special vacuum cleaner is recommended to clean asbestos. If not available, apply a mist of oil or water on the material containing asbestos.
Keep bystanders away from the area. SERVICE TIRES SAFELY Explosive separation of a tire and rim parts can cause serious injury or death.
Do not attempt to mount a tire unless you have the proper equipment and experience to perform the job. Always maintain the correct tire pressure. Do not inflate the tires above the recommended pressure. Never weld or heat a wheel and tire assembly. The heat can cause an increase in air pressure resulting in a tire explosion.
Welding can structurally weaken or deform the wheel. When inflating tires, use a clip-on chuck and extension hose long enough to allow you to stand to one side and NOT in front of or over the tire assembly. Use a safety cage if available. Check wheels for low pressure, cuts, bubbles, damaged rims or missing lug bolts and nuts.
SAFETY 1 - 6 3/12/97 AVOID INJURY FROM ROTATING BLADES, AUGERS AND PTO SHAFTS Keep hands and feet away while machine is running. Shut off power to service, lubricate or remove mower blades, augers or PTO shafts.
SERVICE COOLING SYSTEM SAFELY Explosive release of fluids from pressurized cooling system can cause serious burns. Shut off machine. Only remove filler cap when cool enough to touch with bare hands.
Slowly loosen cap to first stop to relieve pressure before removing completely. HANDLE CHEMICAL PRODUCTS SAFELY Direct exposure to hazardous chemicals can cause serious injury. Potentially hazardous chemicals used with John Deere equipment include such items as lubricants, coolants, paints, and adhesives.
A Material Safety Data Sheet (MSDS) provides specific details on chemical products: physical and health hazards, safety procedures, and emergency response techniques. Check the MSDS before you start any job using a hazardous chemical. That way you will know exactly what the risks are and how to do the job safely. Then follow procedures and recommended equipment. Dispose of Waste Properly Improperly disposing of waste can threaten the environment and ecology. Potentially harmful waste used with John Deere equipment include such items as oil, fuel, coolant, brake fluid, filters, and batteries. Use leakproof containers when draining fluids.
Do not use food or beverage containers that may mislead someone into drinking from them. Do not pour waste onto the ground, down a drain, or into any water source. Inquire on the proper way to recycle or dispose of waste from your local environmental or recycling center, or from your John Deere dealer.
LIVE WITH SAFETY Before returning machine to customer, make sure machine is functioning properly, especially the safety systems. Install all guards and shields. SPECIFICATIONS & INFORMATION CONTENTS Page CONTENTS 3/12/97 2 - 1 SPECIFICATIONS & INFORMATION GENERAL VEHICLE SPECIFICATIONS.
3 METRIC FASTENER TORQUE VALUES. 6 METRIC FASTENER TORQUE VALUE - GRADE 7. 7 INCH FASTENER TORQUE VALUES. 8 O-RING SEAL SERVICE RECOMMENDATIONS. 9 FACE SEAL FITTINGS WITH INCH STUD ENDS TORQUE. 9 FACE SEAL FITTINGS WITH METRIC STUD ENDS TORQUE.
10 O-RING FACE SEAL FITTINGS. 11 O-RING BOSS FITTINGS. 11 GASOLINE SPECIFICATIONS. 12 4–CYCLE ENGINES - NORTH AMERICA. 12 GASOLINE STORAGE. 12 4–CYCLE ENGINES - EUROPE.
13 GASOLINE STORAGE. 13 4–CYCLE GASOLINE ENGINE OIL. 14 4–CYCLE GASOLINE ENGINE OIL - NORTH AMERICA. 14 4–CYCLE GASOLINE ENGINE OIL - EUROPE. 15 BREAK–IN 4-CYCLE GASOLINE ENGINE OIL - NORTH AMERICA.
16 BREAK–IN 4-CYCLE GASOLINE ENGINE OIL - EUROPE. 17 HYDROSTATIC TRANSMISSION OIL. 18 HYDROSTATIC TRANSMISSION OIL - NORTH AMERICA. 18 HYDROSTATIC TRANSMISSION OIL - EUROPE. 19 ALTERNATIVE LUBRICANTS. 20 SYNTHETIC LUBRICANTS. 20 LUBRICANT STORAGE.
20 MIXING OF LUBRICANTS. 20 OIL FILTERS.
20 GEAR TRANSMISSION GREASE. 21 ANTI-CORROSION GREASE SPECIFICATIONS. 22 GREASE SPECIFICATIONS. 23 GREASE - NORTH AMERICA. 23 GREASE - EUROPE. 23 SERIAL NUMBER LOCATIONS. 24 ENGINE SERIAL NUMBER SUFFUX.
24 TRACTOR IDENTIFICATION NUMBER. 24 ENGINE SERIAL NUMBER. 24 GEAR TRANSAXLE SERIAL NUMBER. 24 HYDROSTATIC TRANSMISSION SERIAL NUMBER. 24. 3/20/97 2 - 3 SPECIFICATIONS AND INFORMATION GENERAL VEHICLE SPECIFICATIONS GENERAL VEHICLE SPECIFICATIONS Engine: Make. Kohler Style.Command LT STX30.CV12.5—1216s STX38 (Serial No.
—270000).CV12.5—1215 STX38 (Serial No. 200).CV12.5—1270 STX38 (Serial No.
200 & Motorsport). CV13S—21509 STX46 (Serial No. CV14S—1463 STX46 (Serial No. CV15S—41521 Type. Gasoline, Air Cooled, Single Cylinder, 4-Cycle, Overhead Valves Crankcase Oil Capacity (with filter). 1.8 L (1.9 U.S.
Qt) Oil Type: (Warm Climate).10W30 (Cold Climate).5W30 Electrical: Charging System. Flywheel/Electronic Magneto Magneto Air Gap. 0.2—0.3 mm (0.008—0.012 in.) Charging Capacity.
Boss Amp 250n Manual Lawn Mowers
15 amp (regulated) Spark Plug.Champion RC12YC Spark Plug Air Gap. 1.0 mm (0.040 in.) Battery Type.BCI Group, U1 Battery Reserve Capacity. At 25 amp Battery Cold Cranking Amp.25 amp at 27° C (0° F) for 20 minutes Battery Specific Gravity.
Above 1.225 Points Starter Type.Bendix Inertia Drive PTO Clutch Type. Electric (Manufactured by Warner) Fuel Shut-Off Solenoid (Optional). Replaceable (Below Carburetor Float Bowl) Headlight Kit (Optional). Two Bulbs—Each 12 Volt/23W/1.9 Amp Draw Fuel/Air System: Carburetor Make.Walbro Carburetor Type. Side Draft Throttle/Choke. Unitized Control Linkage Carburetor Fuel Shut-Off Solenoid (Optional).Electric Fuel Delivery.
Gravity Flow Fuel Filter.Replaceable Paper (in-line type) Fuel Type. Unleaded (87 octane minimum) Fuel Tank Capacity. 4.7 L (1.25 gal) Air Filter. Paper Element with Foam Pre-cleaner Muffler Type. Anti-Backfire Power Train: Gear Transaxle— Make. Dana Model.Spicer Heavy-Duty 4360 Transaxle Type.Five-Speed/Linear Shift Domestic Ground Speeds (at FAST idle—3350 rpm) and Gear Ratios: 1st Gear.
(STX30 & STX38 SN —210000 2.2km/hr) 2.4 km/hr (1.5 mph)—61.67:1 2nd Gear. 3.2 km/hr (2.0 mph)—46.67:1 3rd Gear. (STX30 & STX38 SN —210000 4.5km/hr) 5.0 km/hr (3.1 mph)—30.00:1 4th Gear. (STX30 & STX38 SN —210000 5.7km/hr) 6.4 km/hr (4.0 mph)—23.48:1 5th Gear. (STX30 & STX38 SN —210000 8.5km/hr) 8.0 km/hr (5.0 mph)—15.71:1 Reverse. (STX30 & STX38 SN —210000 3.3km/hr) 3.7 km/hr (2.3 mph)—40.00:1 Export Ground Speeds (at FAST idle—3000 rpm) and Gear Ratios: 1st Gear. 1.97 km/hr (1.22 mph)—61.67:1 2nd Gear.
2.61 km/hr (1.67 mph)—46.67:1 3rd Gear. 4.07 km/hr (2.53 mph)—30.00:1 4th Gear. 5.18 km/hr (3.22 mph)—23.48:1 5th Gear. 7.76 km/hr (4.82 mph)—15.71:1 Reverse. 3.04 km/hr (1.89 mph)—40.00:1 Brake Type.Single, External Brake Disc With Dual Friction Pucks. 2 - 4 3/20/97 GENERAL VEHICLE SPECIFICATIONS SPECIFICATIONS AND INFORMATION Power Train: (Continued) Lubrication—Input Shaft Needle Bearings.Unirex® N3 Grease Only Lubrication—Transaxle. Shell Darina® D Grease Only Capacity—Transaxle.0.64 kg (1.406 lbs) Hydro Transaxle— Make.
Kanzaki Model (STX38—early models).Tuff Torq® K50 Transaxle Model (STX38—late models).Tuff Torq® K55 Transaxle Model (STX46).Tuff Torq® K55 Transaxle Type. Hydrostatic Domestic Ground Speeds (at FAST idle—3350 rpm): Forward.
0—9.3 km/hr (0—5.8 mph) Reverse. 0—4.7 km/hr (0—2.9 mph) Export Ground Speeds (at FAST idle—3000 rpm): Forward. 0—7.75 km/hr (0—4.82 mph) Reverse.
0—3.80 km/hr (0—2.36 mph) Brake Type. Single, External Disc Brake With Friction Pucks Lubrication. John Deere Plus-4 10W30 Engine Oil, Class CD Reservoir. Internal Capacity. 1.6 L (3.4 pt) Traction Drive Belt: Gear— Actual effective length.2660±8 mm (104.7±0.3 in.) Theoretical effective length (short). 2631 mm (103.6 in.) Theoretical effective length (long).
2710 mm (106.7 in.) Hydro— Actual effective length.2485±8 mm (97.8±0.3 in.) Theoretical effective length (short). 2477 mm (97.5 in.) Theoretical effective length (long). 2530 mm (99.6 in.) Mower Deck Drive Belt 38-Inch Deck— Actual effective length.2425±10 mm (95.5±0.4 in.) 46-Inch Deck— Actual effective length.3492±10 mm (137.5±0.4 in.) Mower Deck: 38-Inch Mower Deck— Type. Rotary—Dual Spindles (Non-Serviceable) Material Type.Stamped 2.5 mm (0.098 in.) Nominal Gauge Steel Cutting Blade. Two—76 x 5 x 496 mm (3 x 0.2 x 19.5 in.) Blade Cutting Edge.30±5° Angle Blade Wing Lift/Height.40±3 mm (1.57±0.12 in.) Overall Cutting Width. 965 mm (38 in.) Overall Width (w/o discharge chute).
1026 mm (40.4 in.) Drive Type. Single V-Belt (with spring-tensioned idler) Spindle Lubrication. None—Sealed Bearings Lift Type. Manual—Operator’s Station Cutting Settings.Seven: 31.8—89 mm (1.25—3.5 in.). 3/20/97 2 - 5 SPECIFICATIONS AND INFORMATION GENERAL VEHICLE SPECIFICATIONS Mower Deck: (Continued) 46-Inch Mower Deck— Type. Rotary—Triple Spindles (Non-Serviceable) Material Type. Stamped 2.5 mm (0.098 in.) Nominal Gauge Steel Cutting Blade.
Three—50.8 x 5 x 407.4 mm (2 x 0.2 x 16 in.) Blade Cutting Edge. 30±5° Angle Blade Wing Lift/Height. 20.3±3 mm (0.8±0.12 in.) Overall Cutting Width.
1168.4 mm (46 in.) Overall Width (w/o discharge chute). 1308 mm (51.5 in.) Drive Type. Single V-Belt (with spring-tensioned idler) Spindle Lubrication. None—Supplier Fill Only Lift Type.
Manual—Operator’s Station Cutting Settings.Seven: 31.75 mm—89 mm (1.25—3.5 in.) Chassis: Wheelbase. 1135 mm (44.69 in.) Overall Length. 1524 mm (60 in.) Overall Width (w/o mower deck). 908 mm (35.75 in.) Height.
980 mm (38.6 in.) Average Overall Weight STX38 (with mower deck/no fuel).195.05 kg (430 lbs) Average Overall Weight STX46 (with mower deck/no fuel).204.12 kg (450 lbs) Hitch Capacity— Export: Horizontal Pull Maximum.250 N (56 lbs) Tongue Weight Maximum.65 N (15 lbs) Domestic: Trailer Load Maximum. 136 kg (300 lbs) Trailer Tongue Weight Maximum.
23 kg (50 lbs) Steering: Type.Manual—Pinion/Sector Axle Pivot Hub. Shim Adjustable Lubrication.
DuBois MPG-2® Multipurpose Grease Lubrication Interval. 10 hrs (maximum) Toe-In.
6 mm (0.24 in.) — Non-Adjustable Turning Radius. 584 mm (23 in.) Wheels: Size— Front. 6.0 x 4.50 Rear. 8.0 x 6.18 Tires: Size— Front (STX30). 13 x 5—6 NHS (2 ply) Rear (STX30). 18 x 6.50—8 NHS (2 ply) Front (STX38 SN —210000). 13 x 6.50—6 NHS (2 ply) Rear (STX38 SN —210000).
18 x 8.50—8 NHS (2 ply) Front (STX38 SN 200). 13 x 6.50—6 NHS (2 ply) Rear (STX38 SN 200). 18 x 9.50—8 NHS (2 ply) Front (STX38 SN 200 & STX46).
15 x 6.50—6 NHS (2 ply) Rear (STX38 SN 200 & STX46). 20 x 8.00—8 NHS (2 ply) Pressure— Front (with mower deck). 83 kPa (12 psi) Front (with snowthrower). 138 kPa (20 psi) Rear (STX30 with mower deck). 97 kPa (14 psi) Rear (with mower deck).